What did you do to your Raptor today? v2

Started by Krandall, October 02, 2009, 01:00:01 PM

Previous topic - Next topic

Krandall

Quote from: Danny T on October 02, 2009, 08:59:55 AM
drove her through some  water.... she started caughing:( time to drain the oil and flush the engine.

how much water?  ??? ??? ??? ???


Sponsored by:
Yamaha Raptor Forum

PCIII Maps Here:
http://www.krandall.com

Cowards die many times before their deaths The valiant never taste of death but once

Danny T

Quote from: Krandall on October 02, 2009, 01:00:01 PM
Quote from: Danny T on October 02, 2009, 08:59:55 AM
drove her through some  water.... she started caughing:( time to drain the oil and flush the engine.

how much water?  ??? ??? ??? ???

it wasnt even that deep, maybe 1ft... i ran back and forth through it like 4 times total and then she started caughing and dying on me. The engine was having a REALLY hard time starting and there is a brand new battery in there. I opened my lid and there was some sings that water went through the intake (water marks on the bottom of the airbox) but didn't FILL the airbox. anywho tomorrow i will do a complete flush like 4 times.

vreds

I did the same, I wanted to cross a river, but a rock jammed between my chain and rear sprocket, I stalled and the front end got down in the river bed. It was just high enough to enter my air box, my buddy towed me to the river side and the engine was full of water...  :rolleyes:

6 oils change later, the engine finally dropped clean oil  :rofl:

Forgot to put the plug on when i refilled with yamalube   :lol:
Raptor 700 2006 ... now with a dead engine :(

PC5
YFZ front shock
CCP stabilizer
Lonestar axle

1badazz_700r

Put my new g-force axle in today :thumbs: It is a very nice quality piece and is also 4 inches wider than stock

Just a little 778
105.5 WK cylinder CP 11:1
hotrods +5 crank
racersedge +2 head,with webb4
54mmTB with custom intake
sparks X-6exhaust
PC5/w autotune
dynatek programmable
slingshot lockup
+3 stock swingarm
hiper dual beadlocks/w gncc holeshots
flexx bars,burgard+2stem/w antivibe
ASV's
odi's

Blair

went to a local store and found a strip of yellow LED's for $9, bought two sets, and 2 sets of blue ones for my bro inlaw, stocking stuffers ;)

now i have to install them, i am thinking that i am going to run them along the inside of the frame above the engine, if they work well and i like the look ill pick up another set and install them under the hood to put a glow onto the rad
"The Difference Between Genius and Stupidity... Genius Has It's Limits"
"Scars are the Tattoo's of the Brave"
06 Raptor 700 SE - Pro Circuit T4 - PCIII - ASV Levers - AC Racing Nerfs - AC belly Skid (broken) - Holeshot XCR - Pro Taper Raptor Bend Bars - Pro-Tec Prefilter Airbox Lid - HID Headlights -

miguel pereira

After a month of stoppage, finally discoverd what was wrong with my girl. The stock ECU (CDI) died on me...  :'(

Had a friends cdi over and it started at first try.

This was after hours around every wire and plug and bla bla... Error 33 code it said, and that is coil not cdi...

At least now I know what to change to get her running again!  :clap:

And drop a CCP stabiliser also, to welcome her back!  ;)

Alkire193

Ordered Black Barkers, FCI, Quadtech "HUMP" seat, and black Pro Armor Race grab bar. O yea :)

Gunz

Quote from: Alkire193 on October 10, 2009, 11:34:18 PM
Ordered Black Barkers, FCI, Quadtech "HUMP" seat, and black Pro Armor Race grab bar. O yea :)

Noice...especially the hump seat. :nana:


Dent Source LLC

941 +10 w/bar

Colorado700R

Quote from: 4gunz4x4z on October 11, 2009, 09:44:42 AM
Quote from: Alkire193 on October 10, 2009, 11:34:18 PM
Ordered Black Barkers, FCI, Quadtech "HUMP" seat, and black Pro Armor Race grab bar. O yea :)

Noice...especially the hump seat. :nana:

You're into anything that humps you :lol:

Alkire193


Headrope

Da humpty seat, is really neat - so do the hump ...
Two '06 700R SEs

Both with:                                          One also with:                   
GYT-R Sport front grab bar                   GYT-R Swingarm guard
GYT-R Engine/frame skid plate             GYT-R Nerf bars
GYT-R A-arm guards                           OMI Steering stem mount
GYT-R Aluminum radiator guard            ODI Lock-on grips

Colorado700R

is it bad that my nose and glasses look that way normally :(

vreds

Yesterday I washed it clean, repaired my faulty front brake switch ( bad contact IN the switch ) and flipped my rox mounting bracket for handguards to allow the hand brake to be used  :thumbs:

Today, I'm going to beat the hell out of it  :rofl:
Raptor 700 2006 ... now with a dead engine :(

PC5
YFZ front shock
CCP stabilizer
Lonestar axle

Krandall

Quote from: Alkire193 on October 10, 2009, 11:34:18 PM
Ordered Black Barkers, FCI, Quadtech "HUMP" seat, and black Pro Armor Race grab bar. O yea :)

Someone dropped some coinage!!!

Way to stimulate the economy!  :rofl: :clap: :clap: :clap:


Sponsored by:
Yamaha Raptor Forum

PCIII Maps Here:
http://www.krandall.com

Cowards die many times before their deaths The valiant never taste of death but once

11Raptor

Wife got me these to match the fronts for my B-day.... :clap:  hope to get them on today or tomorrow

Michael
-2K7 Raptor700 SE2
-Houser +3/4 Blue Steering Stem
-Pro Taper Black SE bars
-ProArmor Kill Switch w/wrist teather
-ProArmor Skid Plates
-ProArmor FAT Peg Black Nerf's
-ITP Holeshot XCR's on ITP SS112's machined w/black
-Yoshi RS-2 Full Titanium Exhaust
-Quadbox FI Power Box
-2K5 2500 Dodge Cummins 4x4 QC w/35's
-EDGE w/Att.