WTF guys?? Help me out

[RR34]

this should tell you all you need to know. helped me a great deal when i was jetting my POS carb.

http://www.dansmc.com/Spark_Plugs/Spark_Plugs_catalog.html

[pj4553]

Black. I must be too rich?

[RR34]

edited my post instead of making a new one, sorry.


but this will tell you all you need to know.


http://www.dansmc.com/Spark_Plugs/Spark_Plugs_catalog.html

[pj4553]

Cool man. +1 karma. I'm rich. I have no idea how to lean it up a bit. Sometimes I really hate having EFI. If anyone can get me started on using my PC3, reading maps and getting maps to and from the module to my computer I'll be glad to thank you too! 

[RR34]

im a carb man so cant help you there. but trust me. nothing is as bad as jetting :'(

[Bert]

It idled fine but at constant speed at low rpm's it felt jerky and would miss 

   Hard to see what's going on with your plug

Oh.. and I installed my PC3 software. How do I upload my current map to my computer so someone can take a look at it for me?

Can't help you with that, sorry

Try a new  plug & see if the miss is still there

[Bert]

If anyone can get me started on using my PC3, reading maps and getting maps to and from the module to my computer I'll be glad to thank you too! 

I did it the hard way, I read most of the FAQ's with the PCIII software & adjusted my map from 4500 to redline.  My adjustments were headed in the right direction but a dyno smoothed out my tune for me & I haven't thought about PCIII software since.

[pj4553]

Ok I found a map similar to what mods I'm running just a different intake. So all I do is open the map with my PC3 plugged in and hit SEND MAP  and thats my new fuel map?

[Colorado700R]

Ok I found a map similar to what mods I'm running just a different intake. So all I do is open the map with my PC3 plugged in and hit SEND MAP  and thats my new fuel map?

yes 

[pj4553]

Ok. I got my current file. In the notes section it says stock 2006 Raptor 700r. OK? So now I'm trying to pull up the map for the monsters and my current map stays on the page and the new one does not come up. What do I do?

[Colorado700R]

are you opening the monsters map via the "open map file" button???

[pj4553]

Ok I think I got it. I just closed the pages and opened the new file from Krandall's page. Then I hooked up my PC3 to my computer, fired it up and hit SEND MAP. It said map was recieved. Now, when I first hopped on it, my quad stumbled a bit when I touched the throttle then it ran fine. Was that a normal part of the learning process? Also, the map was for Monsters, and Trinity intake. I have a Monsterflow intake. No biggie right?

[Colorado700R]

Ok I think I got it. I just closed the pages and opened the new file from Krandall's page. Then I hooked up my PC3 to my computer, fired it up and hit SEND MAP. It said map was recieved. Now, when I first hopped on it, my quad stumbled a bit when I touched the throttle then it ran fine. Was that a normal part of the learning process? Also, the map was for Monsters, and Trinity intake. I have a Monsterflow intake. No biggie right?

nope, not much difference in the intake.

also did you let the bike warm up before you hit the throttle?  I always restart the bike after I load a map and let warm up for 3-5 minutes

Aaron

[pj4553]

Not really. I did the whole deed while it was running. I waited only about 30 sec then I hit the throttle a couple times and got a little stumble. I got on the quad, backed it out while it stumbled a couple more times and then it was fine.

[kyledvor61]

Not really. I did the whole deed while it was running. I waited only about 30 sec then I hit the throttle a couple times and got a little stumble. I got on the quad, backed it out while it stumbled a couple more times and then it was fine.

so its fine now?