bigbore or stroke it

Started by 1badazz_700r, March 29, 2009, 03:03:27 PM

Previous topic - Next topic

air

I have been told the HR crank for the 700 is close but the YFZ need balanced
Rusty


SANDMAN

Go with the Barker 12m long rod. You'll be good. :grin_nod:

1badazz_700r

Ive heard the same thing as air. whats the difference? suppose i did have it balanced to a certain piston and down the road i change pistons? So know by what you guys are saying i should pull the crank and have it rebalanced again to the new piston. why is balance not an issue with a stock crank you can change pistons all day long. I have heard the hr crank's take almost all the vibration outta the motor compared to stock. a 12mm long rod holly  :mad: thats to much for the type of riding i do :lol:

Just a little 778
105.5 WK cylinder CP 11:1
hotrods +5 crank
racersedge +2 head,with webb4
54mmTB with custom intake
sparks X-6exhaust
PC5/w autotune
dynatek programmable
slingshot lockup
+3 stock swingarm
hiper dual beadlocks/w gncc holeshots
flexx bars,burgard+2stem/w antivibe
ASV's
odi's

Kenny

The Hotrods cranks are balanced for stock weight pistons. Many aftermarket pistons are lighter than stock, which will create what we would call an "overbalance" condition that is not a big deal, and can actually be beneficial for high RPM conditions. Going the opposite way with a larger (heavier than stock) piston should be addressed by having it balanced. Depending on the weight difference, you could possibly bring the assembly back to proper weight by using a lightweight tool steel wrist pin (taper wall will work too). I have plenty of customers using the +5 with 105-105.5 mm bore pistons straight out of the box with no problems. :)
KDS Racing
685 Hope Rd
Floyd VA 24091
NEW PHONE 540-818-9154
Paypal: kenny@swva.net

:satan:

Krandall

how much is it roughly to do the balancing?


Sponsored by:
Yamaha Raptor Forum

PCIII Maps Here:
http://www.krandall.com

Cowards die many times before their deaths The valiant never taste of death but once

francky2000

I am also interested in putting a Hr +5mm crank. I contacted HR and  they also recommend to reduce the by 500 rpm the max engine speed.
thought the info might interest some of you guys

Kenny

Quote from: Krandall on April 01, 2009, 08:14:34 PM
how much is it roughly to do the balancing?
Usually $100-$150
Quote from: francky2000 on April 02, 2009, 01:07:42 PM
I am also interested in putting a Hr +5mm crank. I contacted HR and  they also recommend to reduce the by 500 rpm the max engine speed.
thought the info might interest some of you guys
I wonder why they are saying that.......Maybe they mean the peak torque and HP are 500 RPM sooner. Of course they could be covering their "bases" ???
KDS Racing
685 Hope Rd
Floyd VA 24091
NEW PHONE 540-818-9154
Paypal: kenny@swva.net

:satan:

francky2000

This is what they say exactly:
I would recommend that you lower the RPM by 500. This is mainly due to the thrust angle of the rod and piston and the wear pattern that they make with that stroker.

unquote:



Sand84

So are they saying to lower the rev limit by 500rpm?
2009 Raptor 700- D7 :turbo: :satan:

Custom Carbon Creations

One stop shop for Carbon Covers for Raptor 700!!!

1badazz_700r

well i have been having one problem after another with this thing. so im thinking i may have to admit defeat and have someone else do this. My patience leave alot to be desired and i dont want to screw nothing up because im having a fit

Just a little 778
105.5 WK cylinder CP 11:1
hotrods +5 crank
racersedge +2 head,with webb4
54mmTB with custom intake
sparks X-6exhaust
PC5/w autotune
dynatek programmable
slingshot lockup
+3 stock swingarm
hiper dual beadlocks/w gncc holeshots
flexx bars,burgard+2stem/w antivibe
ASV's
odi's

dabigbratj

the Merchant of Miscellanious Merchandise 

:swinger:

Kenny

Quote from: 1badazz_700r on April 05, 2009, 03:26:59 PM
well i have been having one problem after another with this thing. so im thinking i may have to admit defeat and have someone else do this. My patience leave alot to be desired and i dont want to screw nothing up because im having a fit
Just take the thing apart already... It's gonna be fine :thumbs:
KDS Racing
685 Hope Rd
Floyd VA 24091
NEW PHONE 540-818-9154
Paypal: kenny@swva.net

:satan:

dabigbratj

Quote from: Kenny on April 06, 2009, 08:25:45 AM
Quote from: 1badazz_700r on April 05, 2009, 03:26:59 PM
well i have been having one problem after another with this thing. so im thinking i may have to admit defeat and have someone else do this. My patience leave alot to be desired and i dont want to screw nothing up because im having a fit
Just take the thing apart already... It's gonna be fine :thumbs:
bad your having same thoughts i had at first i still have it all fresh in my mind so we can get it figured out via the phone.kenny told me these same words lol
the Merchant of Miscellanious Merchandise 

:swinger:

1badazz_700r

Im not gonna let this bitch get the best of me :lol: im fresh minded today and sent kenny some naked pictures of his gramma :rofl: i think i made his day :grin_nod:

Just a little 778
105.5 WK cylinder CP 11:1
hotrods +5 crank
racersedge +2 head,with webb4
54mmTB with custom intake
sparks X-6exhaust
PC5/w autotune
dynatek programmable
slingshot lockup
+3 stock swingarm
hiper dual beadlocks/w gncc holeshots
flexx bars,burgard+2stem/w antivibe
ASV's
odi's

1badazz_700r

just messin with ya kenny, i know you liked the forwards :lol:. side cover off and just waiting for the puller to get here in the mail,along with crank,and gaskets from yamaha :thumbs:

Just a little 778
105.5 WK cylinder CP 11:1
hotrods +5 crank
racersedge +2 head,with webb4
54mmTB with custom intake
sparks X-6exhaust
PC5/w autotune
dynatek programmable
slingshot lockup
+3 stock swingarm
hiper dual beadlocks/w gncc holeshots
flexx bars,burgard+2stem/w antivibe
ASV's
odi's