727 Stage 1 Cam?

Started by bustedplastic, February 12, 2009, 09:49:23 AM

Previous topic - Next topic

bustedplastic

So I just got my raptor back together, and here's what I am running.  727 BB (had to bore and replate due to damage), 10.75:1 cp piston, GYTR slip-on, PCIII, and 15t sprocket.   I keep the foam filter and airbox lid on because I go through a lot of water and also ride in very dusty conditions.  I had it out on the ice last weekend and the the pulls hard compared to what it did before, but im wondering if a cam would help the situation even more.  I was looking at the stage 1 hotcam for my setup...

socalrappy700

I think a stage 2 would fit your build nicely, and you may want to consider a set of duals now that you have gone into the engine.
07 SE2

~Erich


Yamaha Raptor Forum

dabigbratj

i have duals im selling as well as a hotcam stg 2 i will be selling it will help open it up even more
the Merchant of Miscellanious Merchandise 

:swinger:

dabigbratj

also i would go at least a stg2 otherwise just waste of money shoot me a pm if you have any intrest
the Merchant of Miscellanious Merchandise 

:swinger:

Krandall

I would say a Stage 1 Cam you won't see much benefit.
Most people you will see are doing the Hot Cam Stage 2, you will (especially with the 727) will see best results out of a little bit bigger cam for the same price. And you can even run the stock springs still.


Sponsored by:
Yamaha Raptor Forum

PCIII Maps Here:
http://www.krandall.com

Cowards die many times before their deaths The valiant never taste of death but once

bustedplastic

Quote from: Krandall on February 12, 2009, 10:37:16 AM
I would say a Stage 1 Cam you won't see much benefit.
Most people you will see are doing the Hot Cam Stage 2, you will (especially with the 727) will see best results out of a little bit bigger cam for the same price. And you can even run the stock springs still.

Thanks for the input guys.  Are there clearance issues with the stage 2 at all, or do the valves just need to be adjusted?  We adjusted them when we put the motor back together, but would they need to be readjusted for the new cam?

Krandall

Yeah, I'd recommend re-clearancing the valves. It's a simple process especially since you'll be right there anyways.  :thumbs:


Sponsored by:
Yamaha Raptor Forum

PCIII Maps Here:
http://www.krandall.com

Cowards die many times before their deaths The valiant never taste of death but once

dabigbratj

you have a pm back and yea you would just set the valves again after instal
the Merchant of Miscellanious Merchandise 

:swinger:

dabigbratj

you have made a wise choice going with duals and stg 2 hot cam you will like the gains
the Merchant of Miscellanious Merchandise 

:swinger:

bustedplastic

Well problem solved, I have the monster duals and a stage 2 hotcam coming from dabigbratj, thanks!

cowtownup

Cowtown...
PCIII
Barker Duals
Pro Design with K&N Filter
Dynojet Ignition Module
Web Cam Stage 3
Diamond Piston (12.5 to 1)
+3 Throttle Body (KDS Racing)
Dynotune Nitrous Kit (Wet System)
SLC +6 Quadcustoms Ladder (PC's Black)
PRM Desert Grab Bar (PC'd Black)
CRJ Lowering Blocks (Front)

Krandall

You get your new stuff yet?!  :clap:


Sponsored by:
Yamaha Raptor Forum

PCIII Maps Here:
http://www.krandall.com

Cowards die many times before their deaths The valiant never taste of death but once

bustedplastic

Quote from: Krandall on March 04, 2009, 02:07:38 PM
You get your new stuff yet?!  :clap:

I did, havent installed it yet though.  No hurry now since the trails are all closed, the ice is melting, and I have no private land to run around on  :(

I have my room mate filling in a gouge on the left pipe, i dont know if the chain did it but it's really thin right there now and hes going to weld a small patch over the spot so it wont punch through...

I suppose i could install the parts and run it down my street, but being as i live two houses down from the police department, i probably shouldnt do that...

socalrappy700

Where do you ride up there?  You're not too far north of me.
07 SE2

~Erich


Yamaha Raptor Forum

bustedplastic

Quote from: Socalrappy700 on March 04, 2009, 02:32:32 PM
Where do you ride up there?  You're not too far north of me.

we usually head up north

clark and jackson county trails, oconto county (pipeline) marinette county, are all trail systems, but they close for the spring thaw...  The nearest thing that will be open the first weekend of april is Dyracuse rec area.  There may be some other parks open, but they dont compare to the trails...

There's the cheese country trail south of where I am, but it's got a 30 mph speed limit and it's flat straight railroad grade...