Rox anti-vibe risers

[machelis]

I put mine on today, they are definitely tight. I rerouted my throttle cable and it was fine after that. I rerouted my clutch about 5 times and I didn't do anything but make it worse. I ended up going down to the speed shop and getting another cable that was about 1/2" longer, it did the trick. I would highly recommend to anybody going with the Rox +2 riser and Flexx bars, go with a +1-2 extended throttle and clutch cables.

How about with the stock bars?

[Gunz]

Kamakaze,

Thanks Bro for the complements seriously means alot. My setup is about 1-1 1/4" over stock. I can't answer yet as far as the Anti-vibe risers and the Flexx bars being redundant till after Saturday (doing a 6-8 hour test run). I do know that after I swapped my stock bars to my Flexx bars, I lost about an inch of height and that was definitely in the wrong direction. If the small of your back hurts and or your wrist hurt or start to numb then your bars are to low. After I put on my Flexx bars I want to raise them about 1 1/2-2 inches. Since Rox offered a 2" anti-vibe riser I figured what the hell, right. I'm going to do some dune riding Saturday and some woods riding on Sunday. After that I'll do a write up in the "product review section"

NaturalRaptor,  Thanks Bro.

Machelis,

I'm just going to throw out a good guess for you and say definitely a +2 clutch cable and throttle cable. They are super easy to switch out too.

[TechQuadShop]

The Elite risers that will allow you to run  either a 7/8" or 1 1/8" bar are now up on our site.

http://www.tqsatv.com/products.php?cat=54

[TechQuadShop]

Yep I need to add the new elites to the site.  Web guy is doing some changes to the website right now to make it even easier to navigate.  Once thats done more products will follow

FYI Steve

Make sure you add the graphics kit too. I get so many people asking how and where I got them!

Our graphics kits are badass!  They are up on the site now and can be seen here

http://www.tqsatv.com/proddetail.php?prod=TQSgraphics

[fire raptor]

I have the standard Rox Adjustable 2" risers with flexx bars and love them so you will be in heaven with both the Flexx and anti vibe. Good choice.

[machelis]

Thanks for the heads up 4gunz. Better safe then a headache 

I'll pick up longer cables when I go for the spacer. Money's a little tight right now due to snowmobile projects and work cutting my hours, so probably this summer 

[Kamakazi]

so 4gunz, did you notice a difference running the rox antivibe?  or is it about the same as just the flex bar?

[Gunz]

so 4gunz, did you notice a difference running the rox antivibe?  or is it about the same as just the flex bar?

I like it even better now. I'll do a full write up later this week. I want to snap some pics and compare stock height vs flexx vs flexx with risers....blah blah blah.

[1badazz_700r]

4gunz was it you that said the houser 1.1/4houser stem was shorter than stock? can anyone confirm this?Iam going to be getting a new houser stem with antivibe clamp and flexx bars. just need to know ahead of time if i still will need a 2" set of risers on top of this.So i can have all the right parts at once for re assembly thanks in advance

[Gunz]

I said that a 1 1/4 houser and flexx bars will be shorter then the stock stem/bar setup. Give me a day or 2 and I'll do a write up with measurements.

[Kamakazi]

hey 4gunz, how tall are u?  and would you go with a higher riser if you were to do it again?  ive been looking at 3.5" riser, and wondering if its enough/too much.  i ordered some new SS cables and was wondering if i needed a brake cable too.  your thoughts please.

[gr8ride4u2luv]

I noticed you had a braided clutch cable... where did yah get that?

[G-Man]

Streamline makes an aftermarket braided clutch cable.  Just checked them out.  I read they are +2" over stock length.  Look like nice stuff.

[gr8ride4u2luv]

Really, I couldnt get anything to come up for the raptor beside the oem black vinyl +2..... I'll try again. Cause Im getting the setup next month!

[gr8ride4u2luv]

Yup, I just tried, could you post a ling to the page. I still cannot find it.... maybe I am just an idiot!