HMF Duals!

Started by Magz, March 04, 2012, 10:26:25 PM

Previous topic - Next topic

Magz

Always wanted barkers duals  but since im a broke beaner......I went the jewest route!  :lol:
My first impression when I saw them done was :shrug: looks cool but nothing special........
now after riding all day on them WOW :woot:  

love the sound, I haven't heard many quads with custom exhaust bud DAMM! this bitch sounds sexy........
with the hmf single it sounded nice but kind of high pitched at higher revs...........
now with the duals it sound deep.......and strong..........like peels likes his men  :nana:

I also noticed it picked up some power on the butt dyno but I wont know that for sure till I take it in to tune.

well with out any further interuptions here are the pics.......

good, bad, tell me what you think.  let me know if you want more pics.










Sand84

2009 Raptor 700- D7 :turbo: :satan:

Custom Carbon Creations

One stop shop for Carbon Covers for Raptor 700!!!

Chillomar




took it for a spin and had to take some pics :jerkoff:
And thats how the cookie crumbles

Magz

omar must like good looking rear ends..........  :lol:


Bert

How was installation?
So they are cheaper than DMC Force 4's ? 

rappyfreak

Very nice compadre! Those headers look really well made and pretty thick like peelsy likes his men  :lol:
'06 Raptor 700: Yoshi RS-7 full, PCV, Pro Design Foam, EHS lid, Flexx bars, 2" Rox a/v risers, ASV C/5 levers, Powermadds, CCP, HDUSA i3500 +2 a-arms, Rap 700 SE front shocks redone by Wiig, Fox Podium X rear, DWT Drift rear and Hiper beadlocks, Pro Armor XC nerfs, Race grab bar, Tag Agro bumper/chassis skid, PRM 0.25" swinger skid

My name is Iñigo Montoya, you killed my father, prepare to die!

funyun

Thats pretty cool, dam that piping is huge!

Magz

Quote from: Bert on March 05, 2012, 06:10:53 AM
How was installation?
So they are cheaper than DMC Force 4's ? 

only cost me $250 for an hmf slip on...... all ready had one.  :woot:



Magz

Quote from: funyun on March 05, 2012, 07:11:16 AM
Thats pretty cool, dam that piping is huge!

THAT'S what im saying.........

my exhaust guy tells me its a true 2" stainless.......... but to me it looks bigger then the barkers 2.25 and 2.5"

I tell you what them bitches flow!


Krandall

#9
Yea, it looks pretty big. Not sure I like how the headers are run so high up. Would have liked to have seen it more similar to how barkers/dmc's are run http://bob2bob.com/images/river/DSC02872.JPG

not quite so high up..

on the left side when sitting on it. how far does the pipe stick out? burn your leg?



But.. all and all.. HMF should have done this.. seriously. love the cans. they look freakin sexy. you should send the pics to HMF tell em lookat this biznatches!!!!


Sponsored by:
Yamaha Raptor Forum

PCIII Maps Here:
http://www.krandall.com

Cowards die many times before their deaths The valiant never taste of death but once

Magz

Quote from: Krandall on March 05, 2012, 07:53:25 AM
Yea, it looks pretty big. Not sure I like how the headers are run so high up. Would have liked to have seen it more similar to how barkers/dmc's are run http://bob2bob.com/images/river/DSC02872.JPG

not quite so high up..

on the left side when sitting on it. how far does the pipe stick out? burn your leg?



But.. all and all.. HMF should have done this.. seriously. love the cans. they look freakin sexy. you should send the pics to HMF tell em lookat this biznatches!!!!


I agree told my buddy to copy the barker routing wich is similar to that pic you posted but
1. pipe is too think to make that turn corectly and
2.pipe was too big to tuck in close to the engine and fit over the starter like barkers do.

Rode all day yesterday and no issues, keeps leg warm but not too bad and I was wearing jeans.........some riding pants would probably be better.......


Peelz

 :clap: :clap: :clap: :clap:

VERY cool.

Way to be a mexi-CAN magz!!!

I've wanted to make a set of these for a long time but...I am an Ameri-CAN'T :rofl:  :rofl: :rofl:
Krandall: "peelz. I'll be real with you. As much as I hate on you for soccer, I really don't mind it"


Krandall

I think jeans would be better than riding pants, jeans are cotton where as riding pants are nylon/polyester which would melt to the pipe.



Sponsored by:
Yamaha Raptor Forum

PCIII Maps Here:
http://www.krandall.com

Cowards die many times before their deaths The valiant never taste of death but once

Magz

ahhhh I'll stick to jeans then.......I've never owned a pair of riding pants...... :lol:

Thats why I took the quad riding yesterday, to evaluate if the pipes by your legs need a guard.........saw some nice universal carbon fiber ones online.....

I dont feel the need for them.........it's staying  as it is.




Peelz

weld on a couple nuts and make a heat shield. you're totally gonna burn yourself on those.  :lol:


keep the kids away from it  :thumbs:
Krandall: "peelz. I'll be real with you. As much as I hate on you for soccer, I really don't mind it"