"Frankenstein Builds"

[Colorado700R]

For those of us who have, or want to build our beasts Our way!!


Post up your mods, and dyno sheets if you got them 

[Krandall]

I wish mine was dyno'd I've been slacking



I have a 10.75:1 CP Piston (105mm)
Hotcams stage 2
Track P&P By Bo White (VelociRaptor)
+2 Throttle Body by Kenny

My barkers
Prodesign intake. UNI Foam & K&N Depending on where I'm riding.
PCIII
Dynatek unmounted. just waiting.

ishock 5500 kit up front

+2 swinger in the back.
RPM dominator 2 axle.

thats all I can think of..

I should be pushin HIGH 50s or low 60's.

[J-HILT]

Umm being built as we speak I will include all the details on thurs with a dyno sheet from Racers Edge

[jdog860]

having a 860 sleeper built 

[russ-russ]

   Current setup is Monster duals  , Texas Quad intake, PC3, Dynatek ignition (curve 2), HotCam stage 2, Kenny's +2 TB, Frankenstien porting is underway and the 11:1 brick is sitting on the dining room table.  Other stuff includes ishock 5500LT front end, ishock revalved and resprung rear, Precision steering stabilizer, ProArmor heelguard nerfs, chassis skid, and rear grab bar, AC front bumper, TrailTech X Bars and clamp with M13 light mount, ProDesign shifter and case guard, Honda thumb throttle, and a shit pot load of tires/wheels.  That just might be all of it.

[kyledvor61]

I got my spark arrestor out :grin_nod: :grin_nod: :grin_nod:

[Sand84]

11:1 Brick with rings
Track P&P By Bo White (VelociRaptor)
Hot Cam Stage 2
LTE duals
Pro Design K&N
PC3

Pulled 52 HP with above mods with a SHITTY TUNE...

For Now

[Havn2muchfun]

Ah come on that tune was spot on, done by perfesionals

[Sand84]

Sure was   I wouldnt let them work on my push mower   Just wait the next Dyno will be good

[Havn2muchfun]

Sure was   I wouldnt let them work on my push mower   Just wait the next Dyno will be good

[Yamahauler]

Lol.. I have been pondering on wether or not to do that many motor mods. It is fast enough but... could be faster. Just don't know if I want to tear into doing it. 

[socalrappy700]

Kenz built 727 with a 12.5:1 Piston.
KDS throttle body
Barker Duals (polished by lowridin88)
trail tech x-bars
trail tech raptor clamp
asv levers
spider grips
motowoz tripple rate long travel shocks
Houser +2 Sli-cast A-arms
T-dub +2 swing arm
Steal braded break lines front and back
Wiggstyle racing rebuilt rear SE shock
RPM dominator 2 axle
OMF beadlocks
Razr 2's all the way around


There could be more, I've lost track.

[SandDragon]

Ok... this is the last time I type all this shit.... 

105mm with sleeve and o-ring
T-rex port from Bo White
+1mm intake valves
Kibble White valves and spring kit
CP 12:1 piston
3/8" bolt kit for the head
+2mm tb bored by KDS
SLC +8 ladder bar arm
Gigot Racing Slingshot lockup clutch
sweet yellow chain from China
Diamond J Customs +6" widening kit up front
YFZ shocks on the front
LC-1 o2 sensor
LTE dual exhaust
custom shaved fenders
Dobeck TFI
Dynatek ignition module
Texas Quad intake
Nitrous Express wet kit 20 shot
Galfer braided steel brake lines
21x12x8  12 paddle Extreme Haulers
Mohawk fronts
Crazy ass driver that doesn't use the clutch to shift and never lets off the gas. 


The machine work was done by professionals... the wrenches were turn by me and my Dad.  The f@cker runs... you wanna race?

[1FST690]

686 Duner

102mm 12.5:1 piston, +1 valves, Web Cam, Kibblewhite springs/retainers, P&P Head, K&N/proflo intake, not much of an airbox, DMC Alien 12 discs, +6 swinger, 12-42 sidewinder gearing/chain, JJ&A Play axle/carrier, 22-11-8 8pdl extremes on 8X8 drag cut wheels, not much for plastic, some bling

Dragbike

106mm sleeved, oringed cylinder, Barker +8mm crank, 14.5:1+ compression, Megacycle X14 cam, Dual 38mm Lectrons on custom intake, dual filters, lots of port work, no 5th gear, no reverse, 1-4 full override, Barker lockup, Drag stem, nothing that is not needed to start or run the bike, -1,+2 drag a-arms, 10X2 Direct Drive spindle mounts "Drive by's" Lightened front spindles, Lightened frame/subframe, custom painted plastics cut tight, powdercoated frame/subframe/steering stem, billit footpegs/grips, +12 swinger, non oring chain and gearing, Pingle Guzzler, struts/shaws/works depending on the sand, 22-11-8 12pdl extremes, JJ&A hillshooter axle/carrier, 8X8 dragcut rears, Barker Drag Pipe header into Looney Tuned cans peg mounted, oh yeah it like alky Its not real fast but it holds its own


RUN YOUR BIKE NOT YOUR MOUTH!

[Jade67]

Barker +11mm Crank
CP 108mm Cylinder
CP 13:1 Piston
9mm Stud Kit
O-ring Cylinder
T-rex Port by Bo White
Kibblewhite +1mm Valves
Kibblewhite HD Spring Kit
Megacycle x-2 Cam
+2mm TB by KDS Racing
No Airbox
RC 650cc Fuel Injector
Velocity Intake w/ outerwear
Monster Inframe Duals
Dynatek EFI
Dynatek Programable Ignition
Direct Drive Lockup Clutch
LC-1 Wideband o2 Sensor
KDS Crank Evac Valve
Shaved Fenders
+8in SLC Ladder bar Swingarm
Non O-ring Chain and gearing
JJ&A Axle
15" Marvin Shaw Hillshooter rear
22x11x8 UL 10 paddle Hauler
Drag Cut Polished Spindles
10x4 Direct Drive "Drive-by" Spindle Mount Wheels
18" Triple Buff Smoothies
16"Marvin Shaw Hillshoter Fronts
No Front Brakes

More fun than a Barrel of Monkies

Maybe forgetting a thing or two but that pretty much sums up my little monster