custom airbox for the wolvy is done (finally... install pics 2nd post 8-24-08)

[Warren]

i got the mods approval. 


thanks man.

[Peelz]

i got the mods approval. 


thanks man.

Like that really means anything.

Nice work. Will that airbox be open on the top, or closed with a vent somewhere?

[Warren]

i got the mods approval. 


thanks man.

Like that really means anything.

Nice work. Will that airbox be open on the top, or closed with a vent somewhere?

yeah it will have like a half top. kinda like this. bolted down around the sides.

[Warren]

so my last peice of pipe showed up today. hurray UPS  i don't think i will be able to finish it up this week but hopfully by the end of next week the box with be done.   :grin_nod:

[Warren]

more pics on page 2.

[Krandall]

more pics on page 2.

NICE!!!! You're doin a great job man. 

[Warren]

more pics added to 2nd post. almost done.   

[Bert]

Looks good Warren, I like it 
Now where is the one for my Rappy? 

[kyledvor61]

damn looks awesome warren!

you should start selling these things

[Warren]

Looks good Warren, I like it 
Now where is the one for my Rappy? 

i just run no lid on my raptor anyway. and plus this one is kind of kicking my ass. lol

damn looks awesome warren!

you should start selling these things

i originally planned to. but then i actually got into it. and i desided against it. like i said to bert this one is kind of kicking my ass. i started fitting up for the mounts on the wolvy. but then found out that i measure wrong and the whole thing was a half inch to long it wouldn't even going down to where it needs to sit. so after cutting that 1/2 inch off. i slapped it in there again to mearsure for the mounts then i cut the first one to short and said "FERK it, i'm done with this for the day". so i just took the carb. off and put my HMF jet in. i'm going to get the front plate welded on at work on monday and hopely then it will make it easier to mearsure for the mounts. since i won't have to hold the front plate level, the box level both ways(front to back and side to side) and try to run a tape measure all at once.

[kyledvor61]

Looks good Warren, I like it 
Now where is the one for my Rappy? 

i just run no lid on my raptor anyway. and plus this one is kind of kicking my ass. lol

damn looks awesome warren!

you should start selling these things

i originally planned to. but then i actually got into it. and i desided against it. like i said to bert this one is kind of kicking my ass. i started fitting up for the mounts on the wolvy. but then found out that i measure wrong and the whole thing was a half inch to long it wouldn't even going down to where it needs to sit. so after cutting that 1/2 inch off. i slapped it in there again to mearsure for the mounts then i cut the first one to short and said "F ck it, i'm done with this for the day". so i just took the carb. off and put my HMF jet in. i'm going to get the front plate welded on at work on monday and hopely then it will make it easier to mearsure for the mounts. since i won't have to hold the front plate level, the box level both ways(front to back and side to side) and try to run a tape measure all at once.

gotcha. but if you get everything down so you can make the same length pieces everytime, it might be worth it.

[BRAD]

looks good man. and you got some dang good loookin welds there

[Warren]

looks good man. and you got some dang good loookin welds there

thanks man.

more pics added in 2nd post. 

[Bert]

looks good man. and you got some dang good loookin welds there

thanks man.

more pics added on page 2. 

do you mean the second post on page 1 ?

I like your work  Warren, nice 

[Warren]

looks good man. and you got some dang good loookin welds there

thanks man.

more pics added on page 2. 

do you mean the second post on page 1 ?

I like your work  Warren, nice 

yep my bad. editing now. and thanks again.