Stock Bottom End w/ 105mm Cylinder & CP 10.75:1 piston

[Krandall]

Howdy folks..

Up for sale today I have a Stock bottom end for sale. It has a VERY low hour crank in it... When I got it, it maybe had 15 hours on it.. (brand spankin new basically). It has new crank bearings in the case. Sitting on top of it is a Bo White Bored/Sleeved 105mm Jug. Tucked inside this lil' diddy is a nice 10.75:1 CP Piston in it w/ rings on it that maybe have 2-4 hours of total ride time on them.
I had this bored out about 2 years ago before stud kits were on the market so when Bo White had my motor, I had the cylinder drilled to accept 3/8" bolts (grade . which was the solution back then. so keep that in mind as well. Doesn't hurt anything. If you wanted to go back to stock size studs, you could heli coil the beast


I'll have some pictures a bit later..

The bad.

This motor just got put back together (By Just.. I mean late sept.. but haven't had time since I got back from LS to dig in) and its been eating HG's like skittles. I'm at my wits end w/ it, so basically starting from scratch. I live a ways away from where the quad is parked so it makes it difficult to find time to actually sit down and work on it/work with it. The Other issue is.. It shifts funky into 2nd gear. Its not hard to shift in, I only noticed it a few times while @ Little Sahara w/ it. Every once in a while it'd hang between 2nd and 3rd. Rode fine, doesn't jerk or anything like that.. Just want whoever gets this to be aware.

About all I can think of off hand..

Price wise I'm asking 800 + the ride.

[Krandall]

750 + the ride

[Krandall]

Bottom end sold. Have a 105mm cylinder and piston for sale still

[Krandall]

Cylinder 150 + shipping

piston 125 + shipping

or

250 for both + shipping

[Krandall]

piston -
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_69430_.jpg
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_69431_.jpg


cylinder -
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_69431_.jpg
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_69433_.jpg

[Krandall]

open to offers. would like to have it gone before week end since I'm headed out to Australia

[vreds]

Hey Krandall, do you still have those ?

[Krandall]

10-4.

Still have cylinder and piston.

[vreds]

maybe I changed my mind...

Can you take a picture of the cylinder bore ? And a picture of the piston side ?

[Krandall]

cylinder
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_76395_.jpg
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_76400_.jpg
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_76399_.jpg
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_76398_.jpg
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_76397_.jpg



piston
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_76396_.jpg
http://i296.photobucket.com/albums/mm194/krandallsfury/292438119_photobucket_76395_.jpg