RaptorSource.com
Other/Off-Topic => Members Rides => Jeep => Topic started by: UncleBeaner on September 24, 2008, 09:26:43 AM
-
over the last few years ive been getting your $200 jeep and patching them up to make a couple runs then parting them out. finally sick of it so i found a nice jeep with lots of potential. its a cj frame that has been back halfed and shackle reversal up front. clean yj tub with a couple surface rust spot but other than that great shape. extra interior,seats, cherry doors,good yj clip,good windsheild frame,35in tires that are almost shot, 258, t-150 , 20 case, dana 44 and 30, spring over ect ect ect
plans for this thing:
fuel injected small block chevy sick of amc motors i think
auto trans for my lady
full cage tied into frame
repair body and put a nice paint job on it
maybe some fullsize axles
put cj clip on it
tube fenders
clock t-case flat
maybe some 37's or 38's or 40's :naughty:
frame sliders
custom bumpers and tire carrier
remove body and paint up frame maybe extra support for common problem areas frame has no rust on it but what the hell
axle gussets
maybe some waggy springs out front to offset axle and xj in rear we will see
and the pics start
before i brought it home~
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff002.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff003.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff005.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff007.jpg)
only rust on jeep~
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff008.jpg)
nephew needed some money so i put him to work.
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/jeepandstreetfair006.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/jeepandstreetfair011.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/jeeps012.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/jeeps017.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/jeeps016.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/jeeps013.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/jeeps009.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff002-1.jpg)
Time to pay buddys in beer
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff001-1.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff003-1.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff002-1.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff005-1.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/stuff004.jpg)
after some more work
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/jeepagain001.jpg)
(http://i5.photobucket.com/albums/y192/unclebeaner/Jeep%20Build/jeepagain002.jpg)
Now im gathering parts and picking away at the frame. cutting out areas and replcing them with 3/16 plate made up my own gusset kit. debating whether to cut back of frame off and 4 link it and coil springs. ill get current pics later.
-
later
TEASE! :lol:
-
Hey Beaner! Let me know what you doing with your build, I am in the final stages of my own build.
-
oh ya and im doing all this in mandas small little garage :lol: but here it is
-
very cool uncle b :clap:
-
looks like alot of work, but will be well worth it...
-
Its a passion. What we go through for our hobbies. Very nice B! :thumbs:
-
cant wait to see the badass finished result
-
today i got a wild hair up my ass and cut the steering box mounting off . it was cracked so f-it no its laying on ground and im like shit i should of measured that stuff :lol:
-
well its been a while but ive been collecting parts but buying this house is cutting into jeep time. have a set of 60's,trans,heater,seats,shifter ect ect ect. need to start cutting for four line stuff :ninja:
-
Looks like a cool project.
I really used to want a Jeep when I was younger, but insurance would have ate me alive!
The Jeep looks like it was in pretty good shape, just a little minor rust issue (which is common for you guys up nort). Easy fix.
I understand the house is cutting into your Jeep time, but the house is more important. The Jeep will still be there when you're ready.
:thumbs:
~Brian
-
i started in on motor im using a ls1 motor at this sec. ms4 cam,port and polish ect.but may have it sold to some guy for his vette.
something like this may be too much for the heep
http://www.youtube.com/watch?v=WSWdty1GuGg
-
i started in on motor im using a ls1 motor at this sec. ms4 cam,port and polish ect.but may have it sold to some guy for his vette.
something like this may be too much for the heep
http://www.youtube.com/watch?v=WSWdty1GuGg
Hell yeah!
Bad ass.
I know a guy that has a TPI motor in his Jeep. It's pretty trick....It turns the tires extremely well.
~Brian
-
fish plate the frame, drop in a bbc, run 3ton military axles 8) or better yet drop in a cummins. looks good beaner, but i think ill be finished my vehicle first. heck i could bring ya them axles and get that interior from ya :grin_nod:
-
Cummins?
Damn. Would it fit?
That's a $14,000 engine.
~Brian
-
4 cylinder cummins out of a massey 220 swather would fit no problem :grin_nod: ive also seen plenty of 5.9 cummins fit where a 6.2 use to sit :thumbs:
-
fish plate the frame, drop in a bbc, run 3ton military axles 8) or better yet drop in a cummins. looks good beaner, but i think ill be finished my vehicle first. heck i could bring ya them axles and get that interior from ya :grin_nod:
wat i need those axles. ya ya i need those pics specs? meet half way? :grin_nod:
-
Beaner!!!!!! Where's the thing sitting now????
-
someone else garage :lol: i finished it and sold it :lol:
-
Damn!!!! gave up?? LOL alot to handle arent they?? I am still plugging away at mine slowly. Mounted the tube fenders and getting the tub ready for a splash of silver and then the real fun starts haha. I just ordered $2G's worth of parts for the front end and that doesn't even include axles :'( Oh well
-
Damn!!!! gave up?? LOL alot to handle arent they?? I am still plugging away at mine slowly. Mounted the tube fenders and getting the tub ready for a splash of silver and then the real fun starts haha. I just ordered $2G's worth of parts for the front end and that doesn't even include axles :'( Oh well
finished it and sold it drove it once and she was gone lol. ill sell anything as long as i make a dollar homes