RaptorSource.com

Raptor 700 Information => 700 Motor Mods => Topic started by: gr8ride4u2luv on April 14, 2010, 10:04:46 PM

Title: This winters build thoughts???? Any suggestions?
Post by: gr8ride4u2luv on April 14, 2010, 10:04:46 PM
So am am budgeting and looking into a new winter build this year. With all the mods in my signature I hit 65hp with a Roosterbuilt tune. I cant complain with the little money I spent but want more!  :nod: I want very much a reliable machine but am always looking for more power. I was thinking of at least this....

105.5mm bore with minimum 12.5:1 compression piston. I dont mind running race gas or 50/50.
Velociraptor TrexII port and polish with +1mm valves.
New cam, I dont know what.
FCI Intake.


I dont want to split the case because I have never done it but I would really like to stroke it as well. What are your guys' thoughts on the reliability of a build of this nature??? I do not want to have to take this think apart every 6 months to replace parts. Also any new cam suggestions would be great!
Title: Re: This winters build thoughts???? Any suggestions?
Post by: Colorado700R on April 14, 2010, 10:24:42 PM
if there's no reason to go big bore why do it?  There's 80 HP stock bores out there.  And that lets you run your stock head gasket.  If you like drag racing. I say try a RE +2 head, 14-1 CP or JE and the FCI.  that alone should push you into the 70's
Title: Re: This winters build thoughts???? Any suggestions?
Post by: gr8ride4u2luv on April 14, 2010, 11:01:54 PM
 Well what am I missing them??? I'm 15hp short?
Title: Re: This winters build thoughts???? Any suggestions?
Post by: Krandall on April 15, 2010, 07:55:55 AM
You gotta remember too.. Every Dyno is different. I'd find out what that 80hp machine aaron's refering to has in it. and then see if Rooster's dyno'd anything similar in build and see what it made for power.

I think some of the next cheaper logical steps would be. Getting rid of that HC3 and moving to something a bit bigger. one of the barker cams or if you can find a RJ. And then a bigger compression piston also will get you a bit more too .
Title: Re: This winters build thoughts???? Any suggestions?
Post by: Colorado700R on April 15, 2010, 08:53:16 AM
Quote from: gr8ride4u2luv on April 14, 2010, 11:01:54 PM
Well what am I missing them??? I'm 15hp short?

bigger nastier head with oversized valves, high compression (14-1)  light weight piston, web 4 cam. 

Barker, Racer's Edge, KENZ, OMW, and I think Bo's Megalondon head, and others...all of them have what you need.  The head seems to be a HUGE factor.  The combonation of porting, valve size, and cam matched with high compression and a good flowing intake and exhaust builds stupid power in the raptor.  I prefer to keep stock bore till there is a need too upgrade (Cylinder wear), then I would pursue a bigbore setup.

Just my $.02

Aaron
Title: Re: This winters build thoughts???? Any suggestions?
Post by: VelociRaptor on April 15, 2010, 10:01:33 AM
I think 65 is real good on that dyno based off of others thats been on that dyno. Stock valve port, only one way to go and thats up. HCIII, only one cam thats commonly used thats smaller so its almost the same situation. If your going to stay with a bored TB go with the +1 head and the 5050 cam or possibly the Web4. If your gonna get a billet TB or possibly sometime soon after go to the +2 head and the Web4 or custom. You will have over 70 with the +1 combination and 80 or so with the +2 combination.